Build Your Own DIY Chicken Plucker: A DIY Guide

Are you tired of spending money on expensive chicken pluckers? Or perhaps you can’t find one that fits your needs? Look no further, because we have a solution for you – a DIY chicken plucker!

Building your own chicken plucker can seem intimidating, but it’s actually quite simple with the right materials and instructions. Not only will you save money by making your own, but you’ll also have the satisfaction of knowing that you built it yourself.

8 DIY Chicken Plucker designs that you can try

1. The Barrel Plucker

This design uses a barrel or drum as the main body, with PVC pipes and rubber fingers attached to the outside. The barrel is cut in half and the PVC pipes are attached using elbow joints and screws. The rubber fingers are made from cut up foam pool noodles and attached to the PVC pipes using rubber bands. To use the barrel plucker, simply place the chickens inside the barrel and turn it on. The rubber fingers will remove the feathers as the barrel rotates.

Advantages: This design is relatively simple to build, and the barrel provides a large capacity for plucking multiple chickens at once. It’s also relatively easy to clean and maintain.

Disadvantages: The barrel plucker may be too large and bulky for some users, and it requires a motor to operate.

Instructions

1. Cut the barrel or drum in half using the circular saw or jigsaw. You should now have two halves, each with a diameter of 22 inches.
2. Cut the PVC pipes into lengths of about 6 inches. These will be used to hold the rubber fingers that will do the actual plucking.
3. Attach the PVC pipes to the barrel halves using the elbow joints and screws. Make sure that the pipes are evenly spaced around the barrel.
4. Cut the foam pool noodle into small, finger-sized pieces. These will be used as the rubber fingers.
5. Attach the rubber fingers to the PVC pipes using rubber bands. Make sure that the fingers are evenly spaced and pointing outward.
6. Put the barrel halves back together and secure them with bolts. You should now have a functioning DIY chicken plucker!

2. The PVC Pipe Plucker

This design uses PVC pipes as the main body of the plucker, with rubber fingers attached using rubber bands. A motor is attached to one end of the plucker using a drill. To use the PVC pipe plucker, simply place the chickens inside the pipes and turn on the motor. The rubber fingers will remove the feathers as the pipes rotate.

Advantages: This design is lightweight and portable, making it easy to move around and store. It’s also relatively simple to build and maintain.

Disadvantages: The capacity of the PVC pipe plucker may be limited, as it can only hold a few chickens at a time. It also requires a motor to operate.

Instructions:

1. Cut PVC pipes into lengths of about 6 inches.
2. Attach the pipes to a motor using screws and a drill.
3. Cut up a foam pool noodle into small, finger-sized pieces.
4. Attach the rubber fingers to the pipes using rubber bands.

Place the chickens inside the pipes and turn on the motor to start plucking.

3. The Handheld Plucker

This design is a simple and portable option for small scale operations. It consists of a wooden handle with rubber fingers attached using screws. To use the handheld plucker, simply hold the handle and use the rubber fingers to remove the feathers from the chicken.

Advantages: The handheld plucker is very portable and easy to use, making it a convenient option for small operations. It’s also relatively simple to build and maintain.

Disadvantages: The capacity of the handheld plucker is limited, as it can only hold one chicken at a time. It also requires manual labor to operate.

Instructions:

1. Cut a wooden handle to the desired length.
2. Cut up a foam pool noodle into small, finger-sized pieces.
3. Attach the rubber fingers to the handle using screws.
4. Hold the handle and use the rubber fingers to remove the feathers from the chicken.

4. The Bucket Plucker

This design uses a plastic bucket as the main body of the plucker, with PVC pipes and rubber fingers attached to the outside. A motor is attached to the bottom of the bucket, and a handle is attached to the top for easy carrying. To use the bucket plucker, simply place the chickens inside the bucket and turn on the motor. The rubber fingers will remove the feathers as the bucket rotates.

Advantages: The bucket plucker is a convenient and portable option, as it can be easily carried and stored. It also has a relatively large capacity for plucking multiple chickens at once.

Disadvantages: The bucket plucker requires a motor to operate, and it may be more difficult to clean and maintain compared to some of the other designs.

Instructions: To build a bucket plucker, follow these steps:

1. Cut PVC pipes into lengths of about 6 inches.
2. Attach the pipes to the bottom of a plastic bucket using elbow joints and screws.
3. Cut up a foam pool noodle into small, finger-sized pieces.
4. Attach the rubber fingers to the pipes using rubber bands.
5. Attach a motor to the bottom of the bucket using screws and a drill.
6. Attach a handle to the top of the bucket using screws.
7. Place the chickens inside the bucket and turn on the motor to start plucking.

5. The Tumble Plucker

This design uses a barrel or drum with a motor attached to one end. As the barrel rotates, the chickens are tumbled inside, allowing the rubber fingers to remove the feathers.

Advantages: The tumble plucker has a relatively large capacity for plucking multiple chickens at once. It’s also relatively easy to clean and maintain.

Disadvantages: The tumble plucker requires a motor to operate, and it may be more difficult to build compared to some of the other designs.

Instructions:

1. Cut a barrel or drum in half and attach the halves back together using bolts.
2. Attach a motor to one end of the barrel using screws and a drill.
3. Cut PVC pipes into lengths of about 6 inches.
4. Attach the PVC pipes to the barrel using elbow joints and screws. Make sure that the pipes are evenly spaced around the barrel.
5. Cut up a foam pool noodle into small, finger-sized pieces.
6. Attach the rubber fingers to the PVC pipes using rubber bands. Make sure that the fingers are evenly spaced and pointing outward.
7. Place the chickens inside the barrel and turn on the motor to start plucking.

6. The Belt Plucker

This design uses a conveyor belt as the main body of the plucker, with rubber fingers attached to the belt. A motor is used to move the belt and pluck the chickens.

Advantages: The belt plucker is a more automated option, making it easier to use for larger operations. It also has a relatively large capacity for plucking multiple chickens at once.

Disadvantages: The belt plucker may be more difficult to build and maintain compared to some of the other designs. It also requires a motor to operate.

Instructions:

1. Cut a conveyor belt to the desired length.
2. Attach rubber fingers to the belt using screws. Make sure that the fingers are evenly spaced.
3. Attach a motor to one end of the belt using screws and a drill.
4. Place the chickens on the belt and turn on the motor to start plucking.

7. The Paddle Plucker

This design uses a series of paddles with rubber fingers attached to them. As the paddles rotate, the chickens are tumbled and the feathers are removed.

Advantages: The paddle plucker has a relatively large capacity for plucking multiple chickens at once. It’s also relatively easy to clean and maintain.

Disadvantages: The paddle plucker requires a motor to operate, and it may be more difficult to build compared to some of the other designs. It may also be more time-consuming to use, as the chickens must be placed in the paddles one at a time.

Instructions:

1. Cut a series of paddles from wood or plastic, making sure that they are evenly spaced and can rotate freely.
2. Attach rubber fingers to the paddles using screws. Make sure that the fingers are evenly spaced.
3. Attach a motor to the center of the paddles using screws and a drill.
4. Place the chickens in the paddles one at a time and turn on the motor to start plucking.

8. The Drum Plucker

Similar to the barrel plucker, this design uses a drum with rubber fingers attached to the outside. A motor is attached to the drum, and as it rotates, the chickens are tumbled and the feathers are removed.

Advantages: The drum plucker has a relatively large capacity for plucking multiple chickens at once. It’s also relatively easy to clean and maintain.

Disadvantages: The drum plucker requires a motor to operate, and it may be more difficult to build compared to some of the other designs.

Instructions:

1. Cut a drum in half and attach the halves back together using bolts.
2. Attach a motor to the drum using screws and a drill.
3. Cut PVC pipes into lengths of about 6 inches.
4. Attach the PVC pipes to the drum using elbow joints and screws. Make sure that the pipes are evenly spaced around the drum.
5. Cut up a foam pool noodle into small, finger-sized pieces.
6. Attach the rubber fingers to the PVC pipes using rubber bands. Make sure that the fingers are evenly spaced and pointing outward.
7. Place the chickens inside the drum and turn on the motor to start plucking.